This Aluminium Oz Hydrofoil Suits: Outboards 2.5hp - 3hp 4 Stroke – All Years Engines - Honda, Mercury, Johnson, Evinrude, Mariner, Suzuki, Yamaha, Parsun, Nissan, Oz Hydrofoil Performance Points: Eliminate – Cavitation/Ventilation Stop – Purposing More – Trim Control, Stern & Bow lift Improve – Fuel economy, Stability & Tracking Plane – Faster & Easier at slower speeds Proudly Manufactured in New Zealand from Quality strong Marine Grade Aluminium Designed specifically to suit each model outboard Stainless bolts, nuts & washers included with Hydrofoil This Oz Hydrofoil is bolted underneath of the outboard cavitation plate Gloss Powder Coated Plate colour matched to the outboard Comes with easy installation instructions & support No Welding Needed Quality Tested and Approved Well proven product with thousands sold worldwide Best Performing Hydrofoil on the market guaranteed! Learn More

This LISTING is for LOCTITE and BOLTS that are used to fix the SKEGGARD to the skeg. From time to time bolts may get lost or loosen. Keep a extra set handy for repairs. Conveinantly packaged in a snaplock bag, containing 4ss BOLTS, 2ss BOLT ENDS and the LOCTITE Glue SKEGGARD are manufactured for 20hp and up. WE KEEP A FULL RANGE OF SKEG GUARDS IN STOCK FOR ALL MODEL OUTBOARDS AND STERNDRIVES SO CHECK OUT OUR OTHER LISTINGS. We are also stockist , and Permatrims, Shore Spikes, and Slide Anchors Learn More

Suits - 40HP PARSUN Outboard 2017 (13 Spline) KEY POINTS: *Revamp your Yamaha Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Skeg guard fits like a glove over both sides of your new or damaged skeg* *ONLY SKEG GUARD ON THE MARKET WITH A FOOTER FOR EXTRA PROTECTION & LONGER LIFE!! *Does NOT affect the performance* *Takes less than 5 minutes to install* ************EACH SKEG GUARD COMES WITH BOLTS, LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ Learn More

Yamaha Out Board, and Yamaha Sterndrives Under Mount OZ HYDROFOIL (BEST SUITED ON BOATS OVER 21 Feet and OVER 2 tonnes)

Suits Yamaha Outboard Motors and Outboard Sterndrives 150 thru to 300 Horse Power
Suits Yamaha Outboards Below: 150 2 Strokes 1986 & Newer F150 4 Strokes 2004 & Newer 175 2 Strokes 1984 & Newer F175 4 Strokes 2014 & Newer 200 2 Strokes 1984 & Newer 200 HP V MAX 2001 VF200 V MAX SHO 2010 & Newer F200 4 Strokes 2002 & Newer 220 HP (Special) 1984-1985 225 HP (Excel) 1987-1988 F225 4 Strokes 2002 & Newer VF225 V MAX SHO 2010 & Newer 225 2 Strokes1986 & Newer F225 4 Strokes Offshore 2010 & Newer F250 4 Strokes 2002 & Newer 250 2 Strokes1990 & Newer VF250 V MAX SHO 2010 & Newer F250 4 Strokes Offshore 2010 & Newer 250 V MAX 2001 & Newer 300 2 Strokes 2004-2007 F300 4 Strokes Offshore 2010 & Newer Yamaha Sterndrives 150HP upwards, single prop. all years NOTE - With any purchase please advise on the Make, Model and Year of your motor. To ensure the correct fit.

With our superior design Oz Hydrofoil you will:

Eliminate - Cavitation/Ventilation


Stop - Porpoising


More - Trim Control, Stern & Bow lift


Improve - Fuel economy, Stability & Tracking


Plane - Faster & Easier at slower speeds


BEST PERFORMING QUALITY OUTBOARD HYDROFOIL ON THE MARKET!!


KEY POINTS:

-Proudly Manufactured in NEW ZEALAND from Quality Marine Grade Aluminum

-Stainless bolts and nuts included with Hydrofoil

-Gloss Powder Coated Plate

-Comes with easy full instructions

-No Welding Needed

-Easy Installation and Support

-Fast and Affordable Shipping

-Quality Tested and Approved

Note: The Standard colored OzHydrofoil for Yamaha Outboards is GREY.

BUY WITH CONFIDENCE KNOWING THE QUALITY AND PERFORMANCE OF THIS OZ HYDROFOIL IS GUARANTEED!!

Learn More

Tohatsu Skeg Guard, Replacement Skeg SKEGGARD suits 40-140hp Tohatsu Outboards KEY POINTS: *Revamp your Tohatsu Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a glove over both sides of your Damaged or Undamaged Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ TOHATSU SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -40-50HP All years (Part#99017) -70-90-115-120-140HP All Years (Pat#99007) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR TOHATSU Learn More

Force Skeg Guard, Replacement Skeg SKEGGARD suits 70-150hp Force Outboards KEY POINTS: *Revamp your Force Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your New or Damaged Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ FORCE SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -70 and 75 HP 2-Stroke 1991-1997 (Part#99017) -70 and 90 HP (By Mercury) 2-Stroke 1998-2002 (Part#99007) -85 and 90 HP 2-Stroke 1988-1996 (Part#99018) -90-120-150 HP L-Drive 2-Stroke 1988-1991 (Part#99018) -120-125-150 HP 2-Stroke 1988-1996 (Part#99018) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR FORCE OUTBOARD Learn More

Honda Skeg Guard, Replacment Skeg SKEGGARD suits 35-50hp Honda Outboards KEY POINTS: *Revamp your Honda Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ HONDA SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -35-40-45-50 HP 4-Stroke 1991 and Newer (Part#99017) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR HONDA OUTBOARD Learn More

Volvo Skeg Guard, Replacment Skeg SKEGGARD suits All Model Volvo Sterndrives KEY POINTS: *Revamp your Volvo Penta Sterndrive Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ VOLVO PENTA SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -SX Drive (Single Prop) 1995-2006 (Part#99022) -DP Drive (Dual Prop) 1996-2007 (Part#99019) -SX and DP Drive 2007-2015 (Part#99020) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR VOLVO STERNDRIVE Learn More

Johnson Evinrude Skeg Guard, Replacement Skeg SKEGGARD suits 150-300hp Omc Outboards KEY POINTS: *Revamp your Johnson Evinrude Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of you Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ JOHNSON/EVINRUDE SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -150-175-185-200-225 HP 2-Strokes 1986-2003 (Part#99008) -150-200 E-TEC (25" and 30" Shaft) 2-Strokes 2004 & Newer (Part#99023) -150-200 HP E-TEC (20" Shaft) 2-Strokes 2004 & Newer (Part#99008) -225-300 HP E-TEC All Models 2-Stroke 2004 & Newer (Part#99023) Does not fit HO Models WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR JOHNSON/EVINRUDE Learn More

Johnson Evinrude Skeg Guard, Replacement Skeg SKEGGARD suits 40-140hp Omc Outboards KEY POINTS: *Revamp your Johnson Evinrude Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ JOHNSON/EVINRUDE SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE - 40 & 50HP (by Suzuki) 4 Strokes 2001 Thru 2003 (Part#99034) - 60-70-90-115 & 140HP 4 Strokes 2001 & NEWER (Part#99026) --70hp Evinrude 1978 (Part#99010) - 75 Thru 130HP Etec (25" & 30" Shaft) 2 Strokes 2004 & NEWER (Part#99025) -75 Thru 115HP Etec (20" Shaft) 2 Strokes 2008 & NEWER (Part#99035) -90-100-115-120-140HP 2 Strokes 1980 Thru 2001 (Part#99010) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR JOHNSON/EVINRUDE Learn More

Suzuki Skeg Guard, Replacement Skeg SKEGGARD suits 90-140hp Suzuki Outboards KEY POINTS: *Revamp your Suzuki Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ SUZUKI SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE 90-115HP DF 4 STROKES 1998 and NEWER (Part#27261) 140HP DF 4 STROKES- ALL YEARS (Part#27261) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR SUZUKI Learn More

Suzuki Skeg Guard, Replacement Skeg SKEGGARD suits DF 40-75hp Suzuki Outboards KEY POINTS: *Revamp your Suzuki Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ****EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!**** SUZUKI SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE 40-50-60-70hp DF 4 Strokes 2003 & NEWER (Part#99017) 13 spline / teeth only Learn More

Yamaha Skeg Guard, Replacement Skeg SkegGuard suits 150-350hp Yamaha Outboards KEY POINTS: *Revamp your Yamaha Outboard Skeg with this great looking SkegGuard in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard / Sterndrive Skeg to Install a Skeggard*
*Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs*
"Now there is a better and cheaper way to repair lower unit Skeg damage"
*Simply bolt on SkegGuard right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage*
*Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE*
*TAKES LESS THAN 5 MINUTES TO INSTALL*
************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************
YAMAHA SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE
-150hp 2 & 4 Stroke 1984 & NEWER (Part#27151)
-175-200-225-250hp 2 Stroke 1984 Thru 2002 (Part#27151)
-200-225-250-300hp 2 & 4 Stroke 2003 & NEWER (Part#27030)
-350HP 4 Stroke 2009 & NEWER (Part#27151)
WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR YAMAHA
Learn More

Yamaha Skeg Guard, Replacement Skeg SKEGGARD suits 40-140hp Yamaha Outboards KEY POINTS: *Revamp your Yamaha Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ YAMAHA SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE -40-48 & 50-85hp CV, 2 Stroke 1984 Thru 2000 (Part#99017) -40-50 & 60hp (13 Spline Shaft) 2 & 4 Stroke 2001 & NEWER (Part#99033) -60-70-90-100hp (15 Spline Shaft) 2 & 4 Stroke 1998 Thru 2001 (Part#99007) -60-70-80-90-100hp (15 Spline Shaft) 2002 and NEWER (Part#99032) 70-90hp 2 Stroke 1984 Thru 1998 (Part#99016) -115-130-140hp 2 Stroke 1984 Thru 2002 (Part#99015) -115-130-140hp 2 Stroke 2003 & NEWER (Part#99029) -115-130-140hp 4 Stroke 2000 & NEWER (Part#99029) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR YAMAHA Learn More

Mercury Skeg Guard, Replacement Skeg SKEGGARD suits 135-300hp Mercury Mariner Outboards KEY POINTS: *Revamp your Mercury/Mariner Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ MERCURY/MARINER SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE - 135-150-175-200hp 2 & 4 Stroke 1978 Thru 2005 (Part#99006) -200hp EFI 2 Stroke 1996 Thru 2005 (Part#99021) -225hp 2 Stroke 1978 Thru 1995 (Part#99006) -225hp 2 Stroke 1996 Thru 2004 (Part#99021) -135-150-175-200hp OPTIMAX 2 Stroke 2 Stroke 2005 & NEWER (Part#99006) -150 Thru 300hp & VERADO 4 Stroke 2005 thru 2015 (Part#99021) -150 Thru 300hp VERADO 2016 and NEWER (Part#99038) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR MERCURY/MARINER NOTE- PART 99038 is not yet on the Drop Down menu, PLease select PART 99021 then let us know that you would like 99038. Learn More

Mercury Skeg Guard, Replacement Skeg SKEGGARD suits 70-125hp Mercury Mariner KEY POINTS: *Revamp your Mercury/Mariner Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ MERCURY/MARINER SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE 70 Thru 125HP Mercury/Mariner outboards 2 & 4 Strokes 1983 and Newer (Part#99007) 75 - 90 - 115HP Command Thrust 4 Strokes. 2015 and Newer (Part#99021) Note: Also suits CT (Command Thrust 60hp) 4 stoke 2015 and Newer. See Listing WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR MERCURY/MARINER Learn More

Mercury Skeg Guard, Replacement Skeg SKEGGARD suits 40-70hp Mercury Mariner KEY POINTS: *Revamp your Mercury/Mariner Outboard Skeg with this great looking SKEGGARD in polished Stainless* * All you need is 2-3 Inches of Skeg remaining to Install a Skeg Guard* *Drill x2 1/4 Inch holes through your Outboard/Sterndrive Skeg to Install a Skeggard* *Manufactured in the USA with thousands sold* *Dont risk damage to seals and bearings with the heat from welding of outboard and sterndrive skegs* "Now there is a better and cheaper way to repair lower unit Skeg damage" *Simply bolt on SKEGGARD right over your damaged or non damaged Skeg.It is quick,its easy,and its stronger than the original,so it protects your Skeg and Propeller from future damage* *Self Draining* *Fits like a Glove over both sides of your Damaged or New Skeg* *Does NOT affect the PERFORMANCE* *TAKES LESS THAN 5 MINUTES TO INSTALL* ************EACH SKEG GUARD COMES WITH BOLTS ,LOCTITE AND EASY TO INSTALL INSTRUCTIONS!!************ MERCURY/MARINER SKEG GUARD MODELS/ PART NUMBER CROSS REFERENCE - 40-50-60-65-70 HP 2 Stroke 1980 Thru 1985 (Part#99016) - 40-50-60 HP 2 Stroke 1986 Thru 2002 (Part#99017) - 40-50-60 HP 2 & 4 Stroke 2003 & NEWER(Part#99034) - 50-60 HP (BIG FOOT Models) 2 & 4 Stroke 2003 & NEWER (Part#99007) - 60 HP Command Thrust, 2015 and NEWER (Part#99007) WHEN ORDERING ONLINE USE THE SIZE DROP DOWN BOX BELOW TO SELECT THE CORRECT PART NUMBER SKEGGARD FOR YOUR MERCURY/MARINER Learn More